Burner Screws

[LMichaels]

Every time I use anti-seize, I look like Tin Man from Wizard of Oz. It is a great product, but far and away the most messy automotive product ever created

not sure why you have this issue. I use it a lot and don't have the issue

 

[Cody Bratton]

I may be over-exaggerating... but the automotive community tends to joke about it more

 

[Samuel]

Although from looking at the description of Permatex Copper anti seize on Amazon it states:

• Suggested Applications: Spark plug threads installed in aluminum, exhaust manifold bolts, engine bolts, oxygen sensors, knock sensors, thermostat housing bolts, fuel filter fittings and battery cable connections.
• Prevents seizing, corrosion and galling where high temperature conditions exist

 

[DanHoo]

Galvanic corrosion needs moisture to be an issue. Probably not a concern on spark plug threads.

I have never used antisieze on spark plugs.

 

[Jon Tofte]

I use the Loctite "lipstick" tube. I think it might be a neater way to apply. With the low volume I use, it lasts long enough for me.

https://www.amazon.com/Loctite-LOC504468-Grams-Copper-Anti-Seize/dp/B0029SZIUI/?tag=tvwb-20

 

[Samuel]

Jon, are you saying you use copper anti-seize on your grills?

 

[Cody Bratton]

We use it to almost paint stuff (bake sides of brake pads that are about the size of a nice ribeye, suspension bolts/nuts). So the jar and wand is an absolute mess, and I dont think the stuff ever fully runs out. There is always somehow still enough in the can

 

[Samuel]

I have used the copper anti-seize on automotive applications, I just have never use in the firebox or my grill applications, thus the reason I asked.

 

[Samuel]

Success! These screws worked for the burners. So now my burners are completely restored. Now to do the fire box.

 

[LMichaels]

I thought you were looking for screws for the air shutters

 

[Samuel]

I thought you were looking for screws for the air shutters

No, I was not. Sorry about the confusion. I was only looking to replace the ones I pictured. Those are the ones I always have issues with.

 

[Samuel]

I big flat head screwdriver helps a lot to get the burners out.

I have some time used a flat tip bit with an impact driver on ones that an impact socket no longer work on.

 

[Jon Tofte]

I have used the copper anti-seize on automotive applications, I just have never use in the firebox or my grill applications, thus the reason I asked.

Yes I have. Never heard of any risk before and anyway almost none would be within the firebox. Comments above seem to go both ways, but if it is really a bad practice I am open to change and advice.

 

[DanHoo]

I think the chance of galvanic corrosion is greater when moisture is readily available as in marine applications. This is where I learned to avoid using copper anti seize with aluminum and stainless fasteners.

Maybe it's not an issue in a cook box where its hot and greasy.

I use copper anti seize all the time on steel. The bottle I have is probably 30 years old.

 

[Bruce]

Same with me. If you get that stuff on your hands and fingers, it is nearly impossible to wipe off.

 

[DanHoo]

Same with me. If you get that stuff on your hands and fingers, it is nearly impossible to wipe off.

A little dab will do

 

[Cody Bratton]

Same with me. If you get that stuff on your hands and fingers, it is nearly impossible to wipe off.

The start of the tin-man

 

[Samuel]

Bruce, I just sent you some screws. Your welcome to let us know if they work holding the grease tray rails, if you'd like.

 

[Bruce]

Ok. That is great. I will let you know.

 

[Samuel]

Just a note those screws have some zinc in them. I would think it would not be an issue outside the firebox. Do you all think it would be an issue inside the firebox. If they are I do have a link to some stainless-steel ones however they are rather expensive.