Search results


 
  1. C

    HeaterMeter 4.2 giveaway

    Nice!! Thanks.
  2. C

    Looking for a HM Board

    Anyone have a spare they are looking to sell or go in on an order?
  3. C

    3D Printed Barrel Servo/Fan

    Tom, If you had to choose between the barrel or in-line fan which one do you prefer?
  4. C

    HeaterMeter Test Cook - Couple of Questions

    Here is my Boston Butt cook. I think the problem with the initial test run was in fact the fluctuation of temps that caused the oscillation before the temps stabilized at 225F. As you can see the HM kept the temps within 5-10F for 12+ Hours. Thanks for the help!
  5. C

    HeaterMeter Test Cook - Couple of Questions

    Ok thanks for the info Tom. I was just running a test last night but I currently have 2 butts going now and since it came up to 225 it has been locked on 225. 1 hour in but will report back tomorrow with the results.
  6. C

    HeaterMeter Test Cook - Couple of Questions

    Lid detection is set to 6%
  7. C

    HeaterMeter Test Cook - Couple of Questions

    Also forgot to mention that I have completed the white wire mod already.
  8. C

    HeaterMeter Test Cook - Couple of Questions

    Yes there should be a good seal on the servo/fan. I have attached a couple of pics below of my setup. The mount is just a make-shift mount until my aluminum tubing comes in on Monday. I have also just replaced the factory Primo gasket with a new one so there should be no air getting in from...
  9. C

    HeaterMeter Test Cook - Couple of Questions

    I have just completed my first HeaterMeter 4.1 test using Tom's Barrel Servo design. For the most part everything worked fantastic but I do have a couple of questions. First off I am using a Primo XL grill with no food loaded and my PID settings were the following: B: 0 P:3 I:0.0035 D:5 I...
  10. C

    HM 4.1, resistors R5, R16, R17, R18

    Thanks for the info! I will order the newer maverick probes and replace the resistors if needed. Any preference between the thermo and maverick probes?
  11. C

    HM 4.1, resistors R5, R16, R17, R18

    If you swap these resistors out for the 22k resistors how low will the temp read with the newer maverick probes?
  12. C

    HeaterMeter 4.1 PCB Wanted

    Anyone have an extra 4.1 PCB they would like to sell?
  13. C

    When one Heatermeter isn't enough.....

    Thanks for the all the info.. greatly appreciated. I will probably just wait until the 4.1 gets the final approval and purchase a single board at that time. Unless someone on here has an extra one kicking around they would like to sell :)
  14. C

    When one Heatermeter isn't enough.....

    Would you recommend a smaller blower? What blower are you currently using? Also where can someone buy a HM PCB?
  15. C

    When one Heatermeter isn't enough.....

    How does the Heatermeter work with the Primo Oval XL? I currently have an XL and a stoker but have not been impressed with the performance of the stoker.
  16. C

    My Jack Daniel's & Maple Syrup Brined Turkey w/Pics

    larry... Can you please clarify something for me? As per your recipe: Per a couple of requests here's the recipe: Jack Daniels Maple Syrup Turkey Container large enough to brine your turkey in (a 5 gallon food grade container works well for large birds) 2 cups maple syrup 1 cup bourbon 1...
  17. C

    Jerky Meat brownish color

    Thanks for the help
  18. C

    Jerky Meat brownish color

    would you still let it air dry for 24 hours and then marinade it for 24-48 hours? or should i skip the air drying now?
  19. C

    Jerky Meat brownish color

    I had the butcher at the local super market slice me 30lbs of top round that was on sale. It sat in the fridge for 48 hours before I vacuum sealed the meat in 5lb bags and the meat in the freezer. Some of the meat was turning a brownish color while some of it was a deep red still. I have made...

 

Back
Top