Joel Dietz
New member
I assembled my first HeaterMeter v4.1.4. Installing the software it hangs up at this spot. What am I doing wrong?
https://flic.kr/p/osaHNv
https://flic.kr/p/osaHNv
I assembled my first HeaterMeter v4.1.4. Installing the software it hangs up at this spot. What am I doing wrong?
https://flic.kr/p/osaHNv
![]()
I have the same problem with my new build.
I get a litter farther but get a screen telling me how to make a cocktail.
I assumed that you would only need the openwrt-rpi.zip file correct and not any of the other files.
All i get on my HM led screen are blocks.
Any help/tips/trouble shooting would be greatly appreciated.
Sam
Ok so I plug in a network cord into the Rpi and I should see a ip address on the LCD nav to that ip and I should be able to config the HM?If you can a screen on how to make a cocktail, you should be good to go.
Hookup a network cord, plug power it in, wait of the ip address to show on the LCD, navigate to that IP via a web browser and setup your options.
Ok so I plug in a network cord into the Rpi and I should see a ip address on the LCD nav to that ip and I should be able to config the HM?
# ifconfig
eth0 Link encap:Ethernet HWaddr B8:27:EB:8C:2B:8C
inet addr:192.168.200.1 Bcast:192.168.200.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:190 errors:0 dropped:0 overruns:0 frame:0
TX packets:190 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:53148 (51.9 KiB) TX bytes:53148 (51.9 KiB)
wlan0 Link encap:Ethernet HWaddr 48:02:2A:9F:A6:C2
inet addr:192.168.1.88 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1789875 errors:0 dropped:1927125 overruns:0 frame:0
TX packets:63454 errors:0 dropped:1 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:437909131 (417.6 MiB) TX bytes:34746491 (33.1 MiB)
Stopping LinkMeter OK
LinkMeter platform is BCM2708
AVR fuses ffd705 OK
b108383042a62f5977c245d134bb9e43 /tmp/hm.hex
hmdude: compiled on Jul 13 2014 at 10:48:38
Using port: /dev/spidev0.0
Loading ihex file: "/tmp/hm.hex" (23604 bytes)
0% | | 0 (0.0s)
0% | | 0 (0.0s)
5% |## | 1182 (0.1s)
10% |##### | 2362 (0.2s)
15% |####### | 3542 (0.4s)
20% |########## | 4722 (0.5s)
25% |############ | 5902 (0.6s)
30% |############### | 7082 (0.7s)
35% |################# | 8262 (0.8s)
40% |#################### | 9442 (0.9s)
45% |###################### | 10622 (1.1s)
50% |######################### | 11802 (1.2s)
55% |########################### | 12984 (1.3s)
60% |############################## | 14164 (1.4s)
65% |################################ | 15344 (1.5s)
70% |################################### | 16524 (1.7s)
75% |##################################### | 17704 (1.8s)
80% |######################################## | 18884 (1.9s)
85% |########################################## | 20064 (2.0s)
90% |############################################# | 21244 (2.1s)
95% |############################################### | 22424 (2.3s)
100% |##################################################| 23604 (2.4s)
Update successful
Starting LinkMeter OK
Done uploading
Is it normal not to see the "no pit probe" message when you first power up the HM 4.1.4?
Jul 21 23:21:20 OpenWrt daemon.notice netifd: lan (499): Lease of 192.168.2.12 obtained, lease time 86400
Thanks Byron. I found my address but it still won't connect and it doesn't display the "no pit probe" which makes be think I have a bad connection.