Search results

Ano - Thanks. I'm actually all up and running now. I decided to go with the reserved ip address for the Stoker to keep from having to figure out how to make it static, and then change the various places I would have had to designate the new address. I'm not online and visible from anywhere...

Awesome. Thank you so much.

All kinds of instructions on how to get a mac or pc to have a static IP address by setting it from the machine, but not seeing how I do this in Airport utility for a device like a Stoker.

Joe - You are awesome. I now have access in an outside my network to my Stoker, and I have it Twittering again. Last favor - All of this is based upon the 10.0.1.36 address it currently has. Can you help me figure out how to keep this static, so that the Airport(s) don't reassign this next...

I can't thank you enough. How are you at getting access from outside the network?

Well I'll be dipped. I get exactly what I'm looking for. I had been entering the full address (extra zero's) but I have always done that, and it used to work.

Got edited there. "D^mn you're good"

**** you're good. Here are results for Stoker (others are similarly good): Ping has started… PING 10.0.1.36 (10.0.1.36): 56 data bytes 64 bytes from 10.0.1.36: icmp_seq=0 ttl=255 time=7.335 ms 64 bytes from 10.0.1.36: icmp_seq=1 ttl=255 time=4.388 ms 64 bytes from 10.0.1.36: icmp_seq=2...

Here's what I get for each address I ping (Airport Extreme, Airport Express, and Stoker): Ping has started… PING 010.000.001.025 (8.0.1.21): 56 data bytes Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 Request timeout for icmp_seq 3 Request timeout...

100% Packet loss on all addresses. Doesn't seem possible given I'm connected to the Airport Extreme. Weird?

Wish I could post pics here, I'd take a screen capture. It currently has "Off (Bridge Mode)" as it's Connection Sharing setting.

set up exactly as described (near as I can tell) here: http://www.eggheadforum.com/in...ew&catid=1&id=830418

Computer is .11 Airport is in "Participate in a WDS Network" mode, and the Airport Extreme is also in same mode, but as the base. Not sure if WDS is equivalent to bridge mode.

10.0.1.1 for the Airport Extreme base station, 10.0.1.25 for the airport express, and 10.0.1.36 for the Stoker

I just sent my Stoker back for firmware update, and now I can't seem to get it back onto my network correctly. I am running a full Mac setup (Airport extreme base station, Airport Express at the Stoker). I have the Airport Express on the network (green light) and can see with the Airport...

Hello all. I had my system running great for almost a year, and all of a sudden, I have nothing. Initially I couldn't log into the Stoker using the ip address that it was being provided by the airport express. I'd enter it, and it would time out. In the process of trying to figure my problem...

I tried to update the firmware today (from a PC on the same network as the Stoker - I could ping the Stoker) and it runs a few of the "Record: addr: ....... and State: addr ......" lines, then says "Requesting upgrade application boot on Stoker Failed to connect." Then I press any key as...

Is updating it that hard? After reading the read me.txt it sounds like I log bit a pc and the stoker onto a single network (enough to be able to see the ip address for the stoker) then run the .bat file and input the ip address of the stoker as the target, right? Took me 3-4 reads of the...

Pretty good explanation (similar to what dann g said, but with detail) on what needs to be done. My only problem is I'm a Mac user so I'm going to need to borrow a PC to do this update to the Stoker. Hope this helps: http://www.kaytat.com/

Okay, so I went to super tweet.net and poked around, and it appears that's someplace I can route my tweets through? If so, I guess i need the Stoker firmware update that has the, whatever it was OAthingy you mentioned, already filled in. Then I'll need to modify with http:// in front of...