Search results

Rene : How did you get those super pictures in your post ?? Looks good enough to eat !!

Bet he is waiting for the fixed ones to arrive to do the current replacement........... I really beleive Darren is on our side. He said the people there were trying to figure the problem like doing tests in the warehouse and all.. He really feels bad about the issue and is not happy about the...

Going back to Antons post with this pic http://photos.yahoo.com/aschoenbacher on page one the black wire was from the factory in hole # 7. I just added the wire to #7 and did not join #5 and #6 and got a Big increase in range. Wonder if anyone has looked inside a replacement with good range...

How do you make sure butts are not greasy when making pulled pork?

A single strand of lamp cord wire is about 18 gauge ......... Or if your really want to buy wire Radio Shack will help you out. Or ask around your only looking for about 1 pennys worth of wire. As far as sheilded it only matters if you are concerned about the wire shorting out anywhere you may...

Todd I like your plan. We use sand in a Brinkman pan which seems to make the lower shelf get more heat and is about the same as the top shelf.

When I used Briqs I removed but reused them as starter fuel. They tend to absorb moisture from the air when left in the ring. Now I use lump and just shake the ring and fill it up again and relight MM . I use Royal Oak Lump from Walmart and get very good size chunks that burn the same time...

Call Darren and ask him .... Why Not ??? Maverick Service....(732) 417-9666 Trust Me he is aware of this forum and our problems.

Page three has the above quote ..Like I said Darren was reading the posts with me while on the phone live time with him. He said he was aware of a crystal ( freq match ) of some units effecting range but not the ant wire issue. Well many of us have added the 6.5 inch wire and have greatly...

I will try the next one at lower temp cooking 235 255 . Then pull the bugger at 130 and rest it . I did the left over from the failed one in a pot simmered in broth till almost fall apart tender. Boy it made some good beef on Cuban bread with the hot juice . We loved the smoky flavour. Thanks...

Well I tried a sirloin tip roast to %145 cooked hot around 325-350. Sliced thin med rare center looked great but !!!!!! Not tender not dry no flavour ( used steak rub ) What should I have done ???? Help please Jim

Go to this site enter the frequency of the signal which is 433 Mhz for the Maverick ET -73 It will calculate for you .. a no brainer . 1/4 wave fits the receiver box and will work http://www.crompton.com/wa3dsp/hamradio/antcalc.html

I called Darren here Tel: (732) 417-9666 Darren Keller is now beyond Customer service and you may have to ask for him. I called pre office hours and got him by chance. Hope this may help !

Phil I know Darren from Maverick read all the posts cause I was on the phone with him after giving him the URL and went thru the list of posts with him live time. He was very pleased to get the info as he had been pulling hair to figure the problem of range also. Al Sivermans post also confirms...

Well I got a few Sirloin Tip Roasts at Winn Dixie on sale for $1.99 Cause they looked good and cheap. Now what should I do with them ???? I have done the search but found little recent results. Help please ?

I called Maverick and spoke to Darren on the missing Ant issue. He was very interested and will check out all our posts here in the forum.

Formula for Antennas is a Basic 1/2 wave is 468/freq So 468/433(freq of Et-73 ) =1.08083 feet Which is 12.9699 inches Now then a quarter wave which is used on stuff like cell phones or handy radios is half of a half wave, or 1/4 wave antenna. So 12.9699 inches divided by 2 = 6.4849 inches...

My Ham radio knowledge says the length is very critical, so based on the picture of Antons original wire trace I made one and soldered it to the open hole. Bill I believe your .54 foot is on the money and is very close to what my add on was. It made a BIG difference in my received range. Also...

Phil : Dang your right mine has NO ANT wire at all. I soldered a wire in the empty hole and ran the wire loop as shown for the original wire in Antons picture and WOW a big big difference in receiver range. Thanks you guys