ISO Genesis 2000 LP Manifold, LP scale/holder and panel (converting NG to LP)


 
Would it be a good idea to try running a leak test on the manifold and hose alone after cleaning the valves and before installing it in the new grill?

And is it proper etiquette to change the thread title?
 
Samuel said:
Always check for leaks. I say.
I guess it would not hurt to take out the ISO. If you can still do so.
Click to expand...
Yes I'm definitely checking for leaks one way or the other, I'm probably overthinking it but just not sure if it makes any difference to wait until before or after I install the manifold

EDIT: looks like I can't change the title now
 
Last edited:
The manifold is pretty shot - leak detector found gas escaping near the regulator and the screws are impossible to get off of the valves, preventing me from cleaning them out. I think for peace of mind I may have to dump money on a fresh manifold.
 
Joe Imburgio said:
The manifold is pretty shot - leak detector found gas escaping near the regulator and the screws are impossible to get off of the valves, preventing me from cleaning them out. I think for peace of mind I may have to dump money on a fresh manifold.
Click to expand...
I was able to get all six screws out of a manifold once. I've tried on many others and my second best was three out of six. That's why I suggested the method I use as opposed to trying to take the valves apart. It works every time and anyone who says it's not the "right" way of doing it is just wrong. As far as your gas leak goes, the brass fitting that screws into the manifold needs to be removed and resealed or the regulator hose fitting needs to be resealed. If neither one of these corrects the problem, the only other thing it could be is a bad hose. If you would rather buy a new one, I would be happy to pay the shipping for you to send me the old one.
 
Last edited:
If it's leaking gas the idea of which way is the best way to clean the valves is moot. If leaking then something else is wrong. But, if dumping oil in a valve was "correct" then they would come with oil in them. They don't. They always come with a tiny bit of grease.
Joe, the oil WILL work and on a manifold not leaking or faulty I've been forced to use it myself. But, I will stand by it's not the best way to do it and should not be used as the first line of work.
By all means use it when necessary. If it saves you buying a manifold of course it's the best thing at that time and for that condition.
But again, if you're getting leakage especially around the stems then don't use the valves. Unless you want to end up like that delivery truck on the video we saw elsewhere. :D
But, I partially agree with Steve. Those screws can be buggers. And I'm not gonna pull my hair out or toss $$$ down the drain, if a drop or two of good ol' ATF will handle the issue.
 
Alright I finally picked this thing up. Took out the NG manifold, which looks to be in good shape. I think it's pretty well cared for - it's a 1998 Genesis 2000 according to SN.

I'd prefer not to try to repair the leaking LP manifold at this point. I think I'll either buy a new one or try one more time to see if someone on here has a LP they could trade for the NG manifold. @Steve Hoch I can look into shipping you the old hose from the busted LP manifold. DM me and let me know what the best way to package and send this is.

I've uploaded pics of the parts. Looks like I should replace the flavorizer bars. Grates look pretty good to me. That round spot on the inside of the lid - is that anything to look into? It seems like it was chipping away a bit if I touch it. I think if I just wash this with dawn and maybe use a putty knife or a razor in a holder I should be able to get it in nice shape.

Open to any other recs. I have plenty of work and family stuff so not necessarily looking to do a whole rehab job on this, just wanted an aesthetically pleasing gas grill and luckily this one doesn't *seem* like it needs much work.

Thanks!
 

Attachments

  • IMG_0276.jpg
    IMG_0276.jpg
    237.5 KB · Views: 8
  • IMG_0277.jpg
    IMG_0277.jpg
    220.4 KB · Views: 9
  • IMG_0278.jpg
    IMG_0278.jpg
    178.7 KB · Views: 8
  • IMG_0279.jpg
    IMG_0279.jpg
    208.7 KB · Views: 8
  • IMG_0282.jpg
    IMG_0282.jpg
    230.7 KB · Views: 9
  • IMG_0283.jpg
    IMG_0283.jpg
    233.3 KB · Views: 8
  • IMG_0284.jpg
    IMG_0284.jpg
    226.2 KB · Views: 7
  • IMG_0285.jpg
    IMG_0285.jpg
    251.2 KB · Views: 7
  • IMG_0286.jpg
    IMG_0286.jpg
    183.4 KB · Views: 7
  • IMG_0287.jpg
    IMG_0287.jpg
    192.8 KB · Views: 6
  • IMG_0288.jpg
    IMG_0288.jpg
    241.6 KB · Views: 7
  • IMG_0289.jpg
    IMG_0289.jpg
    303.5 KB · Views: 7
  • IMG_0290.jpg
    IMG_0290.jpg
    256.2 KB · Views: 8
They show 2. The standard one you linked and the upgraded one. Honestly I'd go for the upgraded one for a few $$$ more. They look like darn good covers. I may even buy a couple for myself. The one on the Wolf has seen better days and the one on the BigZ is getting a little "crispy" and hard to handle. Got them in my shopping list.
Thanks for doing a little leg work for me :D
 
LMichaels said:
They show 2. The standard one you linked and the upgraded one. Honestly I'd go for the upgraded one for a few $$$ more. They look like darn good covers. I may even buy a couple for myself. The one on the Wolf has seen better days and the one on the BigZ is getting a little "crispy" and hard to handle. Got them in my shopping list.
Thanks for doing a little leg work for me :D
Click to expand...

Also, I ended up going with this costco grill cover. Wanted something more resilient and aesthetically pleasing and liked that it still had the air vents.

I'm not going to be able to store it in the garage between uses like the previous owner, but hopefully this is enough to keep in it good shape. This guy really kept it in great condition.

 
Joe Imburgio said:
We did it fellas, she works. Thanks for all the help. Hoping to get a cook in tonight or this weekend.
Click to expand...

Good job !

Flames look decent.

You might try cleaning the burners where there are yellow tips and you may be able to improve the flame to an even blue. A little elbow grease and a SS wire brush across the openings on the burners sometimes will open the flow up a little and clean up the flame.
 
I gave them a SS brushing when I first got it, but to be honest there were no visible obstructions in any of the holes. I used compressed air as well. I'm going to see how well it gets up to temps. If I don't see any obstruction in the burners, how vigorously should I scrub?
 
You must log in or register to reply here.

 

Back
Top