Search results

How do I reform the door? Should I put on end in a vise and pull on the other end?

I have a very old (> 20 years) 18.5" WSM and recently installed a BBQ Gasket nomex kit. I have a Cajun Bandit after market door, and glued the gaskets on the three inside sides of the door to rest on the exterior of the WSM and for the fourth side, I glued the gasket on the outside surface...

I have a very old (> 20 years) 18.5" WSM and recently installed a BBQ Gasket nomex kit. I have a Cajun Bandit after market door, and glued the gaskets on the three inside sides of the door to rest on the exterior of the WSM and for the fourth side, I glued the gasket on the outside surface of...

Take the thighs and attached legs off of the turkey and place them on either side of the turkey. Turkey will cook faster this way. My brined turkeys typically take around 90 minutes at 300F to get to 155F in the breast and 170F in the thighs.

What type of SD card do you have? I just built a new 4.2.4 HeaterMeter, loaded up a Sony 70MB / second SD card with the software, and never could get the Raspberry Pi to write to it. I was using an Ethernet connection to the HeaterMeter and not WiFi. Later gave up and purchased a cheap SanDisk...

Friday, June 24, 2016 - 4:00 PM to 10:00 PM Saturday, June 25, 2016 - 11:00 AM to 8:00 PM Parking: $10 per car Santa Clara Central Park 909 Kiely Boulevard Santa Clara, CA 95051 http://www.svbbq.com/ This is a KCBS event. Chris, are you attending/judging?

Given you are using copper pipe, a great thermal conductor, does heat from the WSM fire get conducted to the point where it could melt the plastic on the blower? If this is a problem, can you add a stainless steel spacer (a very poor thermal conductor) to thermally insulate the plastic blower...

I am assembling the 4.2.4 PCB and am confused about the assembly directions. I have identified the 1K and 4.7K resistors and the places on the PCB to solder them. However, the picture of the resistors installed on the PCB are different than the resistors shown on the resistor legend above that...

Is 175 micron resolution OK?

Are the current files you posted on ThingVerse setup for the MG90 servo or do I need one or several different files to accommodate that specific servo?

Using the MG90 servo. Do I need to print anything differently?

Getting ready to print my Adapt-a-Damper. What material should I use ABS or PLA?

Here are the specs from the announcement: A 1.2GHz 64-bit quad-core ARM Cortex-A53 CPU (~10x the performance of Raspberry Pi 1) Integrated 802.11n wireless LAN and Bluetooth 4.1 Complete compatibility with Raspberry Pi 1 and 2 https://www.raspberrypi.org/blog/raspberry-pi-3-on-sale

Can you tell me what files to print for a complete V2, 2 hole damper?

Is there a print file that allows this new version of the V2 Adapt-a-Damper to attach to the BBQ Guru Weber / Universal fan adapter?

Can anyone help me to get an Adapt-a-Damper printed? Happy to pay for consumables and shipping. If so, please PM.

Bryan recently PM'ed me about v4.3: - v4.3 is coming out in a month or so - v4.3 will not contain any new features but is a HM redesign to allow Raspberry Pi+ and Raspberry Pi2 boards to be used. - v4.3 is dimensionally bigger and more expensive by a few dollars. - If you have an existing...

I live in the San Francisco Bay Area and would like to acquire an Adapt-a-Damper that will connect to my BBQ Guru WSM fan adapter. I do not have a 3D printer and would pay for shipping and the consumables. Is there anyone on this thread that can print one and ship it to me. If so, please PM.

I have an 18.5" WSM and have a fan but not a servo damper. PID: B=4 P=3 I=0.005 D=5

I have often put 15-17 pound packers into my 18.5" WSM by cramming it between the grate handles. After 5-6 hours it shrinks down enough so it lays flat.