Search results

I only picked one up at Microcenter yesterday, they were 5 bucks if you bought one but if you bought more than one they were 9.99 each. I just checked the stock and they are already sold out. I'll keep an eye out for you though.

I picked up mine yesterday, I can't believe just how small this thing is.

Well over night last night I got to do my first test (too busy last weekend to get a chance to mess with it) Anyway here is the graph, started with the default PID settings then settled on P=2.5 I=.0035 D=6. But I didn't change that until after it was up and running. Learned that startup max...

I just wanted to say Thank You! The design of the offset rotary damper is awesome. I built v4.2.4 just for the servo support, this is my third HM. Anyway heres a pic of the latest setup, it goes on its madien voyage this Saturday: (printed with MadeSolid PET+ amazing stuff if you haven't...

Well, a reboot of the router and the HM and I can connect :) Time to BBQ

I followed the guide, I first removed the wireless interface I first added and followed the guide step by step. I still don't get an IP address showing up on the Interfaces page: Is that something with my router? I just use the router that AT&T gave me.

Yes I left the LAN interface on 192.168.200.1 but I had it connected to my laptop and my laptop disconnected from my wifi while configuring it. I didn't see many steps on getting the wifi set up on the wiki, has it all been brought up here before? If so I can search the thread again.

Apparently I forced it to fit the wrong way. Flipped it around and all is well, now I just need to figure out how to talk to it wirelessly. I got it connected to my wifi network but when I go to the address that my router assigned I get a connection error.

I wanted to share that I got my Heatermeter up and running last night :) The only problem so far is the 4 way button doesn't work, only the down button seems to work and that's only after wiggling the button from left to right while pushing it down. Any suggestions on where to look?

Quick question about blower motors, you said earlier in the thread that "Any 12VDC fan can be used as long as the current draw isn't too high." My question is what is the maximum current draw the blower can have? I have the one in the parts list but need more CFM for my big offset smoker. I...

Got it connected, thanks. I was thinking it worked as an access point that you connected to. Now to figure out this LCD.

If you make it a client on your network how do you go about accessing it from a mobile device like an iphone.

I figured out what locked up the router, whenever I go to the wifi tab and try to enable the wireless the little cricle just spins and spins while it waits on the router to reconfigure. I let it sit for 15 minutes last night before rebooting it because I couldnt do anything else. After the...

Just wanted to check back in, I was able to reset the configuration of the router(finally got putty to work so I can ssh in) and now the pages work again. Also figured out how to burn the bootloader using the burn from any atmega method. I did notice with doing that I had to uplug the ardiuno...

Now is reflashing the same as before or do i need to change "tftp -i 192.168.1.1 put linkmeter-wrt54g-squashfs.bin" comand to point to 192.168.200.1?

I can get to the login in page, and I set a password. After I log in I get the Linkmeter configuration page but if I try to go to any other page I get page not found. Whats the easiest way to wipe it clean and start over tonight?

So I think I messed up the router already, not sure if its in fail-safe mode or not. 192.168.200.1 still brings up the main page but when I try to go to the configuration I log in and any other page I try to go to I get a page not found error. After that I can't get back to the main page...

Success! Thank you Bryan! The linksys is now flashed correctly, now its time to connect the heatermeter to it

Thanks Bryan, exactly what I needed. I'll mess around with it tonight and report back.

Hey guys, awesome work so far. I was able to get a PCB from Duston and I have it all put together. Pretty Sure I have the ATMega programmed correctly, I used another Arudinuo to program it. Where I am getting hung up at is flashing the router. The router I got off ebay came loaded with...