Search results

Hi, What/where is B parameter? In configuration i see only P, I, and D... I’m currently struggling to set up my wsm 18’(47cm).

tnx. I think being 18' smaller it should react quicker than 22, so values should be different, but I can start from yours ;)

Hi Guys, does someone have PID values set for WSM 18' (47cm)? I'm using adapt-a-damper if it may matters Tnx a lot L.

Hi Everyone! Good news!!! It is working now!! It was Q5 mosfet broken. ...step by step I've purchased a raspPI 3B not + installing stable version...and I still had the problem. Actually I had that even in manual mode without rasp connected . Then it must had to be the circuit. Following the...

Hi WBegg, thanks a lot! Resistor should be ok since tester gives me aroung 1k on board...but I tested them all before mounting, since I'm little color blind...and all of them were ok. So I'm going to concentrate on mosfet (Servo one should be Q5)...I'll unsolder and test "offline"... Hope is...

Hi All, another day of testing... after had unsoldered the RJ45 plug I put multimeter directly into holes in the board, and if I put red in 5V and black in SERVO holes, I see a contact. Is that normal? If servo line should be 0,xV and i have same value of 5V, my idea is that somewhere 5v gets...

Hi Todd, thanks for helping. I've unsoldered the RJ45 plug from HM board, and tested again pointing tester on holes in the board. I still have same voltage in signal-gnd and 5v-ground (4.97v). So issue is before, but I'm not able to identify it...checking all pins I seem there are no bad...

Thanks Steve, just tried, and I have same issue. Good news, RasPi is ok...bad news I have really no idea what else to check :P

Hi, assuming I've tested everything else I can imagine (details here: https://tvwbb.com/showthread.php?75023-Heatermeter-amp-Adapt-a-Damper-All-ok-but-Servo-is-not-working May be the Rasp PI 3 B+ the cause of not working servo or randomly work for few seconds only? I tried 0,5A, 1A, 2A power...

Hi Dave, I've actually checked two (or more) pieces of everything: - 2 servo - several eth cables - 2 eth plug adapt-a-damper side - 0,5A, 1A and 2A power supply I've also checked in the board for all pins that seemed to have "air" in the holes and soldered again Only thing I haven't...

Tested also with 2A power supply. Still not working. I’ve read signal is a 3.3v line, but I have same tension of 5v line (4.95v) when unplugged and little less (4.65v) when servo is plugged... there may be a short around soldered eth plug or somewhere around there? These tensions are ok?

I'm posting a video...easier... Initially it's dead, then I move a little signal wire, and it has some random movements. At the end it worked for a while...after the end of the video, after 2 minutes, without touching anything else than control buttons moving from 0% to 100% it's dead again

Hi Jeff, thanks for suggestion. I've purchased a new power supply 12V 1A Very strange behavior: at very first start up it worked. I switched off to unscrew the piece from adapt-a-damper to align it when fully open. Switched on and it's dead again. Actually it moves if i touch the contact on...

same set up same problem Any idea about what worked exaclty to fix it? I have same behavior fan perfect, servo dead, actually servo moves a little (seems random) if i move or touch signal wire on the contact, and for few seconds it worked in some cases seemed to work good, but was really 2 or...

Hi guys, just landed here, my first post. I've just assembled the HM using raspberry 3b+ with adapt-a-damper. Everything seems ok except the servo SG90 I connect it with RJ45 cable cat 5E, with a following B schema so: pin 3 (white-green) -> servo pwr 5v (red on SG90) pin 4 (blue) -> gnd...

Just landed here. Hi everyone!!!