Search results

Well that's the reassurance I was looking for before cranking on this thing. Squished either end together with a few F clamps from harbor freight and a 2x4 a bit wider than the side tables. The cast aluminum was way more malleable than I imagined.

i'm just concerned with the cast aluminum. I shattered a cast iron burger press trying to get the handles tighter by coaxing them closer with a hammer. Don't want to do this with an irreplaceable bottom.

Recently got a used 2012 Genesis E310. Picked it up for $25 and replaced a missing drip tray and liners to get it going! First time started using it and noticed on either side the top cover when closing the side edges hit the bottom base. The top/bottom clash just in front of where the...

Here’s the rd3. https://www.dropbox.com/scl/fo/m67fyb9pp5kfhpht11ord/AJFsNgLI95HavQENOxTlpZ4?rlkey=oqa4w54rxloohqogmxp8pbmhf&st=thtgyrtg&dl=0

https://drive.google.com/drive/folders/0B1qMo4bilbhhYldEdVpzRlh2UGs?resourcekey=0-eqdX4sggUaUOh-_Q8EvuJA

Make distillery reservations ASAP! They will fill up on the weekends even in October. Bardstown Bourbon Co restaurant is really good food. Hughly suggest thier rickhouse tour. You get to thieve samples from three barrels and they give you a glencarne with the tour. Scout and Scholar is also a...

IIRC you have to select that there is a thermocouple connected in the software. The software setup allows for various types of temp probes to be selected of various ohms or thermocouple type. if the wrong type of probe is selected the temps will be drastically off.

Ever try a separate different thermocouple?

With a good ducted system installed it is really hard to justify installing new heads throughout a home. I would say MN will be one of the last to transfer out of NG. It's too dang cold for heat pumps to perform properly. Rochester internationally airport design day is -9F. Remember the...

What brand and when did you get three heat pumps and 7 heads for $2500? That seems crazy low. I'm a PM for a mech contractor as well as mechanical engineer. I will say our company seems to lean towards the Mitsubishi/Trane systems and I know they are very proud of them when they send invoices...

Did you increase the size of any ductwork intake or venting capabilities of the smoker to account for double the air volume?

0.36a is the max amp draw. Not the constant amp draw. This amp draw will occur normally at the maximum amount of airflow with the least air flow resistance. Add enough air flow resistance and the amp draw would get less. It's moving less air and doing less work. Do you have a fan curve for...

Did you change temp probe type in the software?

https://tvwbb.com/threads/battery-setup-questions.85852/#post-968094 https://tvwbb.com/threads/fyi-battery-for-heatermeter.76264/#post-867808 https://tvwbb.com/threads/heatermeter-on-battery-success.62170/ Check these out. It doesn't take much. You maybe able to back into an mAh based on...

I literally put my smoker up this afternoon and saw the cluster of wires and heater meter parts and thought.... Man, I need to do something to store all this stuff better. Your setup looks good! Thanks for your contributions to this community!

Water heater elements would be a bad idea. They would burn up because the air wouldn't conduct heat away from the surface of the element as fast as water would. The infrared would not be good at heating all the surfaces of the wood. Think lizard on a rock, the infrared lamp mainly heats the...

Hmm. Quickly out of my realm of expertise. Reformatting will erase the card and all is contents. Then you would have to download the firmware for the heater meter source code and load it back onto the SD card after it is reformatted. If I recall correctly the first time you load a...

Gosh. What a way to remember a friend. So sorry for your loss. You need to put the SD card into your computer and open up the coding to edit the password and wifi address inside the heater meter code. Whatever WiFi you want it to log into you type it out it exactly in the blanks. Be sure you...

I am not of any help but knew exactly what you are up against. One possibility would be to use a relay or SSR for the larger fans. One with personal experience would be better off to provide some insight for you though.

Bryan- this was a cutoff of a roll of soft copper. Just happened to be about the right diameter. Sometime you are lucky, sometimes you're good. I happened to be lucky :)