Search results

I got me HM fully up and running today but couldn't figure out why my ambient temp was almost 30 degrees F high after putting in the correct coefficients. It was baffling me until I realized that my HM had been on for about 25 minutes with me trying to get it connected to my WiFi network. I...

SUCCESS!! Here is what I did. 1. Took Ralph's advice and since I had plenty of solder on the backside I just put the iron back on and wiggled the pins to try and get better flow. Not perfect through flow since I can see gold still on alot of the frontside pins. Put the Mega back in and...

Ralph, Tried the suggestion and it comes back with "permission denied". Does that tell us anything other than it doesn't see me as it's master:) EDIT: I just had a thought. I used an existing SD card that I have used and tried to image it with my mac running parallels. When parallels...

Thanks Ralph. How did you eventually get the solder to flow to both sides. I read your post about flowing to both sides so I tried to not be stingy with the solder but it would just build up on the back side of the board instead of flowing through the hole. I noticed that almost all of my...

Thanks Ralph. I will try that tomorrow. Was I not patient enough the first time and could have interrupted the initial boot phase? I waited a couple of minutes before unplugging it.

Got a problem! Any ideas (Solved) Ok, got everything done and tried to power it up tonight. Started with the 12V since I didn't read the instructions that stated it is preferred to use the micro USB for first boot. Upon power, the first and third lines on the display are solid rectangles...

That is really nice! BTW- I keep forgetting to ask if you are using PLA or ABS?

Thanks Ralph! That is what mine looked like. Funny how the metal film resistors colors are so off.

Thanks Bryan. Now I can keep soldering and getting it finished.

Started building mine today and I have a question that I probably should have asked a few hours ago. Here is the issue. I ordered from the Mouser links on the HM Hardware Wiki page. They appear to be correct based on the part number labels on the bags the resistors came in but the resistors...

I must be working on 76 then.

Looks sweet! Can't wait to see it working with the HM and hooked up to a WSM. I will want one!

Really really nice work!! That things looks sweet! I am sure I missed it but what type of paint did you use? Edit: Never mind, I just read your post on the Painting the Mini WSM for what type of paint you used.

Hi Mark, I can't quite make out the wording on the packages as to exactly what these are. What section in Home Depot did you find them? Thanks Troy

Thanks RJ, I ordered several of these. A few for future HMs.

RJ, Would you happen to have the part number for the 90 header on the HM board? I am getting ready to order from Digi-Key. Thanks for all of the help. I went ahead and ordered the display you recommended off of eBay. Thanks, Troy

Thanks guys. I went ahead and purchases the jacks specified in the parts list. Do you knowmifmthey make a high heat 72/73 smoker probe or could I use a food probe as the smoker probe? I couldn't find the 72/73 smoker probe longer than 3'.

Thanks RJ for the link. I will order one of those this evening. That is a crazy good deal!! Can't wait to get everything in and start putting it together. Thanks, Troy UPDATE: ordered one this evening. Thanks for the link.

RJ and or Bryan, Found this display on Digi-key. Would it work? I realize that since the connector is on top that I would have to use a cable but not really a big deal to me. http://www.digikey.com/product-detail/en/NHD-0420DZ-FSW-FBW/NHD-0420DZ-FSW-FBW-ND/2607002 Thanks, Troy

Still trying to nail down an order from mouser but I have a question about probes. I noticed that the parts list states ET-72 or ET-73. I have looked and can't find any 3' or preferably 6' smoker probes for the ET-72/73. I have found them for the 732 though and would prefer to use longer lead...