Recent content by Alex_Seed


 
  1. A

    Servo Power

    I am having problems getting my heatermeter back up and working, Blower works fine but I am not measuring 5V on the Servo power, any ideas?
  2. A

    HeaterMeter Hardware v4.3.3, v4.3.4, v4.3.5, v4.3.6

    Has the Heatermeter project died?
  3. A

    POE

    I wasn't thinking of using a HAT rather I was thinking of using one of these, that splits the power and ethernet. This one provides 12V (supposedly at up to 2A) through a jack compatible with the heatermeter and and Ethernet tail to plug into the RaPi. I have tried it, not connected to the...
  4. A

    POE

    Has anyone run a heatermeter via POE. At 25W will that be enough power?
  5. A

    HM 4.3 Case to bolt to a panel

    I am wanting to replace my HM 4.2 with the 4.3 version (4.2 will be used elsewhere) but I need to be able to bolt the casing to the inside of a thin Aluminium panel on my smoker. With the 4.2 I just DL a design off Thingiverse, but I do not seem to be able to find a suitable one for the 4.3...
  6. A

    No Pit Probe

    Sorted. It was the ATMega328 that had gone bad. Replaced it and it is all good :-)
  7. A

    No Pit Probe

    I have a feeling that water may have got into my heatermeter (it rained) and it is now not recognising the pit probe, a K type Thermocouple and the display just says "No Pit Probe" Also Probe 2 and 3 are working but Probe 1 is not recognised. But maybe it is the TC that is faulty, what sort of...
  8. A

    Thermocouple not Matching the temps on ThermoWorks

    I am having problems getting the Thermocouple match the temps given by the thermistor probes. I tested the Thermoworks probes in boiling water and ice water and they seemed pretty accurate. But the thermocouple readings are off, I cannot easily take the TC out to test in BW and IW so I matched...
  9. A

    Twitching Servo

    Any idea what could be causing this? https://photos.app.goo.gl/1VTR3j2gLzYv5Uou8 The servo does this then at other times just moves to 80%ish open and just stalls leaving the vent open.
  10. A

    Large fan won't start at low power

    My word, what a difference having a large fan has made, it could take hours to get this big gravity fed up to temp before, now it is just minutes.
  11. A

    Large fan won't start at low power

    Think I have sorted it by changing from voltage to PWM
  12. A

    Large fan won't start at low power

    Looking in the manual I read about something called *********************** Low Fan Speed (below 10%) When operating in automatic mode at fan speeds below 10%, the fan will run in a partial duty cycle. The fan will run one second out of every ten for each percent required. This special low...
  13. A

    Large fan won't start at low power

    I dont think that that would work as it would just turn it on, not regulate the speed.
  14. A

    Large fan won't start at low power

    I have setup my heater meter and it all looks to be working apart from one thing. If I set the fan speed manually then the fan will only start from rest at about 80-85%, you can then throttle down to about 50% but it just stalls below that. I am using a 6A 12V supply. Is there any settings in...
  15. A

    RJ45 Wiring

    It seems to be wired "oddly", I contacted the manufacturer and received this. am I right in thinking that that is "odd"?
See more

 

Back
Top