Results 1 to 4 of 4

Thread: Heatermeter on Pellet Grill

  1. #1
    New Member
    Join Date
    Jul 2018
    Location
    Texas
    Posts
    4

    Heatermeter on Pellet Grill

    I recently purchased a Pit Boss 820 because it was on sale at Lowes for $400. I've done my research and found that it has issues with large temperature swings which brought me to the Heatermeter. I know this topic has been explored before, but I've only seen discussion. It doesn't appear that anyone has actually posted a successful method for setting up a pellet grill using the Heatermeter.

    For those of you not familiar with how pellet grills work, I will give a short explanation. There are 4 major components: the auger, fan, igniter, and fire box. On startup, the igniter is lit and the auger feeds pellets to the fire box. The fan will start up and this will give you an initial burn. If startup is successful the fire box will have a flame and pellets are fed into the firebox where they are burned throughout the cook. In the case of the Pit Boss, the pellets are fed to the fire box through a user determined duty cycle. The length of the duty cycle is determined by the "P-setting". The auger will always run for 18 seconds each duty cycle. The length of "off" time will be set by the "P-setting". Higher "P-settings" mean longer duty cycles generating more smoke. As you can imagine, this creates the large temperature swings.

    I am going to connect the auger to the Heatermeter in place of the fan. An SSR will need to be added to take the 12V input voltage from the HeaterMeter and control the 120V fan. The fan settings for the Heatermeter will be adjusted to pulse mode. This will mean the fan (auger) will be ON/OFF. My duty cycle will be a set 20 seconds and the auger ON time will now be variable instead of a set 18s using the OEM controller.

    I believe this will work out well, but the part I'm struggling with is the start up. I was thinking about having the fan, igniter, and auger attached to toggle switches to swap them to manual mode and do the startup manually. However, is there a way to automate the startup? I was thinking maybe an alarm that would run the auger, fan, and igniter if the temperature was below X degrees. This would also help recover from a flame out during a cook.

    Any thoughts?

  2. #2
    New Member
    Join Date
    Jul 2018
    Location
    Texas
    Posts
    4
    Going to do my first cook this weekend with no controls to try to understand the pit a little better. I believe everything that I am looking to do can be controlled through programming. However, I have limited knowledge on the programming. I was still thinking of using the same concept as above where the startup is performed manually. I'll switch it to auto mode where the auger will be controlled by the HM "fan" pulse function. The fan will be 100% and the igniter will be set to off.

    I'm also considering tinkering with the fan. I think having two PID loops controlling the auger and fan will get complicated. Instead I was looking at having the fun run a fixed ON/OFF duty cycle. The thought here is that the fan will run for x number of seconds to keep the fire going and will shut off for y number of seconds to let the fire die down and hopefully produce more smoke than a 100% ON fan.

    I think this can be done using the programming, but not sure if I'm going to be able to figure that out. So I was looking to connect the fan to an adjustable cycle timer circuit that I found cheap on Amazon https://www.amazon.com/exec/obidos/A...V863MR/tvwb-20

  3. #3
    New Member
    Join Date
    Jul 2018
    Location
    Texas
    Posts
    4
    So I'm looking to finally start this project. Here is my electrical schematic:


    What I came up with is a manual override on
    1. Fan
    2. Auger
    3. Igniter

    I use the override on start up to
    1. Feed the pot pellets
    2. Turn the igniter on
    3. Turn fan on once pellets have fire

    I use the override on shut down to:
    1. Run the fan to burn out what's left in the pot.


    Once start up is complete, I turn all overrides off and control is given to the HeaterMeter. I will have a 20 second duty cycle where the Auger & Fan will be 100% on OR Auger off & Fan at a %setting.

    I'm trying to get a "burn phase" where I build temp, but then a "smolder phase" where I stop feeding fuel and I drop the fan speed. I hope this will create more smoke.

    I just ordered the Heatermeter parts. I'm going to wait to order the rest of the circuit in case there is any input that might change it. Looking forward to hearing what you guys think!

  4. #4
    New Member
    Join Date
    Jul 2018
    Location
    Texas
    Posts
    4
    Pretty sure I achieve the same result with a much simpler circuit:



    The "Fan Override" will be kept closed. When the solid state relay contacts close, they will override the variable fan speed setting and operate the fan at 100%....at least I hope
    Last edited by KyleH; 09-07-2018 at 02:06 PM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •