Results 1 to 8 of 8

Thread: Gasket kit

  1. #1
    TVWBB Super Fan
    Join Date
    Dec 2000
    Location
    Sherman, Tx, USA
    Posts
    251

    Gasket kit

    I had bought a used 18.5" couple of years ago. Have had a lot of trouble keeping temps down. Once it gets going pretty much have to close all the vents and then still runs over 250. My old one was always rock solid. I finally broke down and bought a gasket kit which I am going to try to install this weekend. Guess going to try using some scotch bright to clean up. About to bring my old WSM back out of retirement. Got a lot of good years on it.

  2. #2
    TVWBB Emerald Member Dustin Dorsey's Avatar
    Join Date
    May 2014
    Location
    Burkburnett, Tx
    Posts
    3,220
    Scotchbrite might be too abrasive. The blue stuff might be ok, but the green is definitely too much. Some 0000 steel wool and simply green and some elbow grease might be the way to go.
    22.5 WSM, 22.5 OTS, Smokey Joe, Genesis 1000, Smokenator 1000, Old Country Pecos, Thermapen, Smoke, Maverick ET-732, Igrill 2

  3. #3
    TVWBB Super Fan
    Join Date
    Dec 2000
    Location
    Sherman, Tx, USA
    Posts
    251
    Quote Originally Posted by Dustin Dorsey View Post
    Scotchbrite might be too abrasive. The blue stuff might be ok, but the green is definitely too much. Some 0000 steel wool and simply green and some elbow grease might be the way to go.
    OK. Thanks

  4. #4
    TVWBB Fan DBono's Avatar
    Join Date
    Jun 2016
    Location
    North NJ
    Posts
    196
    Hi So how did the gaskets work out?
    Dan
    Shirley Fab 24 x 36 RF WSM 22--Smoky Joe Grill- Weber Hanging rack-Cajun Bandit Rotisserie-Rib O Lator-2 Mavericks 732 Thermapen KCBS

  5. #5
    TVWBB Super Fan
    Join Date
    Dec 2000
    Location
    Sherman, Tx, USA
    Posts
    251
    Quote Originally Posted by DBono View Post
    Hi So how did the gaskets work out?
    Dan
    Have not had time. Hopefully this coming weekend. Been working on house, hot tub and yard. This heat wearing my out. Will need to get done before July 4th.

  6. #6
    TVWBB Pro
    Join Date
    Feb 2017
    Location
    East of the Quad Cities, IL
    Posts
    875
    I HIGHLY recommend adding the gasket material to the DOOR and not the center section.

    I wish I had done that...
    Bill: WSM 22.5 BBQ Guru DigiQ DX2 : Maverick ET-733 : BHG Gas Grill: His & Hers John Deere Lawn Tractors

  7. #7
    TVWBB Super Fan
    Join Date
    Dec 2000
    Location
    Sherman, Tx, USA
    Posts
    251
    I think most of the leaks are from the top. Seems warped and does not sit down very good. I bought it from a guy that just moved and probably gotted dropped. Also the vents don't seem to fit like they should like they had been bent and pushed back again. May have to replace them as well. They is really nothing wrong with my old one. I bought it from a guy from this forum many, many years ago. Just determined to get this one working right.

  8. #8
    TVWBB Super Fan
    Join Date
    Dec 2000
    Location
    Sherman, Tx, USA
    Posts
    251
    Well gasket install went fairly well. Let it dry for a day and hopefully can still get it back together. I think the bottom is going to be tight. I stretched the gasket a little as I put on. Will half to adjust door. I had drilled the knob out and just put a bolt and nut on it. Will have to go back and put some kind of spacer on it probably. I had a spare vent from years ago when dog ate two off smoker. Installed that on the worst one. The other two look good. I never use water and last time I did to try to keep temp down and forgot about it. Water pretty nasty and smelly. I normally use the clay pot bottom wrapped in foil. Easy cleanup.
    Last edited by Brian Trommater; Yesterday at 10:49 AM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •