Page 1 of 3 123 LastLast
Results 1 to 10 of 21

Thread: ChadRex's WSM mini Supply List

  1. #1
    TVWBB Fan ChadRex's Avatar
    Join Date
    Jun 2013
    Location
    Redondo Beach, CA
    Posts
    112

    Cool ChadRex's SJS Mini WSM ( with images)

    Well I finally found the right pot, Hispanic markets seem to be the way to go. No crimping!

    Well on my way to start my build.
    Here is Parts List I tried to include part/SKU #'s and prices. Will update as I go along.

    Miscellaneous Tools Needed:
    • Jig Saw with fine metal cutting blade or Metal Cutting Sheers (AKA: Tin Snips, Aviation snips)
    • Measuring Tape
    • String 16" (To measure distance between grate mounting bolts)
    • Scratch Awl - To mark/pre-drill
    • Goof Off - Paint prep wipes: clean residue off Aluminum Stock pot (mine had label adhesive)
    • Metal File or 150 grit metal sand paper: To sand off the sharp edges/burs from cutting bottom off and drilling holes
    • 1/4 inch metal drill bit: for grate mounting bolts
    • 3/8 metal drill bit for mounted thermometer and temp. gauge grommet
    • Church key can opener or 3/4 inch drill bit to drill holes in vent damper cover can



    Some the small hardware I already had in my tool box (the stainless hex nuts and washers)
    I did have to purchase a Jig Saw $59.00 and metal cutting sheers $12.00 at Home Depot, I didn't have these in my tool collection & sure I will need them for other projects so the cost of this will not be included in the overall total cost of my Mini WSM project. I realised I didn't need the jig saw the tin snips would have done the job fine. However cutting the Expanded metal for the charcoal grate was much easier with the Jig saw, using tin snips on expanded metal take more time and effort.

    VMI 32 Qt Steam Pot-

    Purchased at Best Way Hispanic Super Market- for $16.34 (tax included)
    Lid fits perfectly and the pot sits snug in kettle,cooking grate fits nicely in steamer ridge very stable .
    Distributed by VM International
    1241 E Watson Center Rd
    Carson CA 90745
    (310)952-9000


    Charcoal Grate and cooking grate stop Bolts
    • 1/4x3/4 Stainless Hex bolts x6 - @.36 - $2.16
    • Weber plated steel Smokey Joe cooking grate model 7431 - $7.49 Home Depot SKU 150-748
    • 1/4 stainless steel Cap Nut x 6 @1.18 each $7.08 HD SKU 762-132
    • 1/4 stainless steel lock washer 6 pack $1.18 each HD SKU 517-275
    • 1/4 stainless steel hex nut 4 pac x2 @$1.18 each $2.36 HD SKU 307-319


    Temp Gauge Grommet
    Made with Westinghouse brass lighting fixture parts found in Home Depot lighting section.
    • 1/8-IP Zinc-Plated Nipples (8-Pack) need the 1/2" size- $2.97 HD SKU # 215-872 -
    • Brass Plated Nuts and Washers (6-Pack) $1.57 HD SKU # 217-360
    • 1/8-IP Brass Caps (2-Pack) - $1.98 HD SKU# 215-910


    Expanded Metal Charcoal basket
    Still contemplating on this design Flared vs standard 3" deep
    • Expanded Sheet Metal plain 24x12 x 1 -$9.37 HD SKU 474-584
    • Weyerhaeuser 16.5 Gauge-Rebar-Tie-Wire ( to connect coal basket & attach to coal grate) -$3.98 HD SKU#572-365 ( to connect coal basket & attach to coal grate)


    Water/Drip/Diffuser -Still searching for a suitable Water/drip Pan
    • looking for a stainless 9"x 2" deep cake pan, that will cut trimmed to sit on the steamer ridge/lip.
    • Found a deep stainless Steel bowl at 99 Cent Store & some 9" alumn round cake pans 3 @ .99 - $2.99- Not sure if i will use these, still deciding on the set up i will use
    • In a pinch I have 9" round cake pan i can use (I raided my wife's baking supply hoard of pots and pans.)


    Damper/Vent Handle- Lower
    I was fortunate enough to have the damper control rod from a 1 touch cleaning system kit I ordered a few years ago hoping to upgrade my 22.5 " 1980's Weber kettle (It didn't quite fit my 22.5 " I am glad I kept the parts) hopefully the diameter of the Damper handle isn't too big should be Ok
    *Large Ash Catcher- 9"ALU Pie pan .99

    Finishing ( Painting /Sanding)
    Still considering my options for painting/ finishing. My 6 year old son is helping with the design,our thoughts are for anodized Blue Flames with orange tips or 2-tone Orange flames on Anodized Blue Surface, with the dampers, grill legs painted to match. I will NOT be painting the SJS kettle, it has a good finish and the black looks good.
    • Norton Metal Sand paper Assorted Pack- $5.97 HD SKU135-534

      I Still need to order the following
      VHT Engine Enamel up to 550 F ( VHtpaint.com/CariD or TCP global
    • Anodized Base Coat VHT SP453 TCP $8.98
    • VHT Gloss Clear High Temp Engine & Drivetrain Coating VHT SP145 $6.98
    • VHT Anondized Color coat SP451 =anodized blue $8.98
      Application and drying instructions http://www.tcpglobal.com/spraypaintd...ne-enamel.aspx


    Estimated Total Cost of this project= $87.16 (Based on purchasing the above items listed) My cost was more around 75.00 not including the SJS.

    I will do my best to document the steps and update posts.
    Mahalo to all for feedback, replies and suggestions
    Last edited by ChadRex; 07-14-2013 at 01:16 PM. Reason: Added Images/Change title

  2. #2
    TVWBB Fan ChadRex's Avatar
    Join Date
    Jun 2013
    Location
    Redondo Beach, CA
    Posts
    112
    I started my SMJ Mini WSM build on Sunday afternoon.

    • Cut the bottom of the Steamer Pot ( Using the steamer tray as a template to trace the hole)
    • Added a bottom damper/vent handle (from a One-Touch cleaning Kit bent slightly to fit) held in place with a 5/16 e-clip
    • attached 9" Aluminum Pie pan to replaced the ash catcher ( .99 picked up 3 of them) & temporarily marked open and closed position on catcher will add a more cosmetic permanent reference point after painting.
    • Added a Top Damper/vent handle used a stainless steel T-Knob drawer pull
    • Added grill grate holes: 4" from under the top lip of steamer.


      (3 1/4" stainless hex bolts with lock nuts, attached cap nuts on outside.
    • The second grate sits in the ridge of the steamer where steamer tray would rest. Perfect fit!
    • Added a temperature grommet just above where top cooking grate sits, located centered under the handle.
    • Started the 3"high Expanded Metal Charcoal Basket.


      Attaching the EM to the grate has proven to be difficult, I'm using Weyerhaeuser 16.5 Gauge-Rebar-Tie-Wire ( to connect coal basket & attach to coal grate) -$3.98 HD SKU#572-365 and the stuff isn't the easiest to work with. Finishing this tonight, it will be 3" high non flared also added a 2" can for vent damper.


    I still plan on adding a permanent Temp. Gauge to sit just below the top grate. This will have to wait until I pick one up. not sure on the best type . <---any suggestions?

    Once the temperature gauge is installed It will be ready to paint, Still deciding on the paint.The base will be anodized Blue,
    Will also be painting the legs and damper handles.

    I am eager to fire it up, but will patiently wait until it is completely painted.

    Will add pictures to this post as I take/upload.

    a Big Mahalo to everyone who has posted their builds, inspiring and motivating me to take on this fun and surprisingly simple project. My old man is now wanting to build his own.
    Mahalo to those who have responded to my questions and posts, the active communication and generosity in the members here make this a wonderful online community, I will "pay it forward" as others have to me.

    Almost finished... updates to follow.

    Aloha,
    ChadRex
    Last edited by ChadRex; 07-14-2013 at 01:15 PM.

  3. #3
    TVWBB Super Fan Don Fry's Avatar
    Join Date
    Jan 2006
    Location
    Locust Grove, GA
    Posts
    334
    I am assuming from your parts list that you plan on using your thermometer primarily as a backup to your digital. Regardless, the only advice I can give you is to get the shortest stem possible and think through the positioning so that it will not interfere with emplacing and removing the lower grate.
    99 and 09 Performers, 18.5 WSM, 22.5 and 18.5 OTG, SJG, mini WSM, Summit 420, Q100, KJ Classic, KJ Jr, Tripod Schwenkgrill

  4. #4
    TVWBB 1-Star Olympian Tony R's Avatar
    Join Date
    May 2012
    Location
    San Berdoo, CA
    Posts
    13,375
    Very cool. Great detailed post.

  5. #5
    TVWBB Member
    Join Date
    Apr 2013
    Location
    Long Beach
    Posts
    32
    Looking good Chad.

    I wish I would have documented my build better. It was on the back burner so long that when I had a chance I jumped on it.

    The paint is a vailable at the local autozones. I haven't painted mine but will soon.

  6. #6
    TVWBB Fan ChadRex's Avatar
    Join Date
    Jun 2013
    Location
    Redondo Beach, CA
    Posts
    112
    Auto zone does carry VHT and other high heat paints, however they do not have a wide selection of colors.
    I am still looking for the paint I can order through Amazon or through TCP.

  7. #7
    TVWBB Fan ChadRex's Avatar
    Join Date
    Jun 2013
    Location
    Redondo Beach, CA
    Posts
    112
    Don,
    Thanks for the reply. Appreciate your tips. I will definitely take these things into consideration.
    I gather by reading most of the posts, that the Weber branded or Tru-Temp are the way to go.

  8. #8
    TVWBB Fan ChadRex's Avatar
    Join Date
    Jun 2013
    Location
    Redondo Beach, CA
    Posts
    112
    Progress:
    I still need to paint. Ordered the paint from Amazon, should arrive next week. couldn't find the colors i needed at local auto retailers, Amazon ended up being the least expensive.

    Also need to install permanent thermometer.
    However most of it is done. I will take final pictures and total cost once complete. Pictures below, please excuse the messy garage.



    Last edited by ChadRex; 07-28-2013 at 07:16 PM.

  9. #9
    TVWBB Emerald Member Bob Ivey's Avatar
    Join Date
    Apr 2013
    Location
    Winnetka, CA (San Fernando Valley)
    Posts
    3,196
    Chad, if my garage looked that good my wife would be very, very happy. Build looks great. Keep posting as you make more progress.
    2013 WSM 22.5 , 2008 C&B Performer 22.5 , 96 Genesis 1000 Redhead , 1995 Smokey Joe , 2 HeaterMeters, Vortex

  10. #10
    TVWBB Fan ChadRex's Avatar
    Join Date
    Jun 2013
    Location
    Redondo Beach, CA
    Posts
    112
    Build finished all that is left is the paint..





    Chadrex's-SJS-Mini-WSM-(with-images)
    Last edited by ChadRex; 07-14-2013 at 01:45 PM.

Page 1 of 3 123 LastLast

Similar Threads

  1. BBQ Gloves from Tractor Supply
    By Bryan B in forum Barbecuing
    Replies: 9
    Last Post: 08-24-2012, 06:43 AM
  2. Recommendations for on-line restaurant supply
    By John Henderson in forum Kitchen Equipment & Gadgets
    Replies: 11
    Last Post: 04-22-2011, 06:05 AM
  3. 12V Stoker Power Supply
    By Aaron Moore in forum Automatic Temperature Control Systems
    Replies: 4
    Last Post: 01-11-2010, 03:29 AM
  4. Restaurant Supply Store in CLT
    By Jeff Smith in forum Kitchen Equipment & Gadgets
    Replies: 7
    Last Post: 01-19-2009, 05:09 PM
  5. need lump charcoal supply
    By les in forum Barbecuing
    Replies: 6
    Last Post: 07-22-2004, 03:32 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •